We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Nobody downloaded yet

Lab Report Example

Comments (0) Cite this document
According to the equation elocity (McGill and King 12), momentum is directly proportional to the velocity of the car. In the results of table in question [1], as the velocity increases the momentum also increases linearly.
7. A fast moving car is likely to cause more…
Download full paperFile format: .doc, available for editing
Polish This Essay93.7% of users find it useful
Lab report
Read TextPreview

Extract of sample

Download file to see previous pages A small velocity means the car will stop at a shorter distance. Hence the distance will decrease.
The ramp will be set up as in the previous lab experiment with the ramp raised 45 cm above the floor. The meter rule will be stacked at the center of the ramp with its zero mark placed at the bottom end of the ramp. An ultrasound reflector will be taped at the back of the model car. The mass of the car is then measured and recorded. A book of about 300g is placed at the 30cm mark from the bottom end of the ramp. The motion detector is fixed at the higher end of the ramp according to the setup in the lab manual. The motion detector is channeled to the computer interface through channel one. The computer is then set for data acquisition. The car is placed at the 80 cm mark on the meter rule. The car is released simultaneously with the sound from the detector. After the car hit the book the distance which the book moves is recorded. Repeat twice and find average of the distance the book moved. The whole procedure is repeated but now with a book of 600g.
To confirm the results for question [9], we repeat the above procedure but now recording average velocity of the car weighing 500g. The procedure is repeated but with a car of mass 1000g. Again the average velocity of the car is recorded. These velocities are used to calculate the momentum of the car at the time of ...Download file to see next pagesRead More
Cite this document
  • APA
  • MLA
(“Lab report Example | Topics and Well Written Essays - 500 words - 6”, n.d.)
Lab report Example | Topics and Well Written Essays - 500 words - 6. Retrieved from https://studentshare.org/physics/1659700-lab-report
(Lab Report Example | Topics and Well Written Essays - 500 Words - 6)
Lab Report Example | Topics and Well Written Essays - 500 Words - 6. https://studentshare.org/physics/1659700-lab-report.
“Lab Report Example | Topics and Well Written Essays - 500 Words - 6”, n.d. https://studentshare.org/physics/1659700-lab-report.
  • Cited: 0 times
Comments (0)
Click to create a comment or rate a document
Lab report
Name Instructor Course Date Lab report Following the field work in wabashiki wetlands rivers cape, which was conducted in order to establish the types of the soils found the texture, the composition, and the porosity of the soils. The study was undertaken in groups of between 4-8 people; where each was required to pick two samples.
3 Pages(750 words)Lab Report
Lab Report
Calcium phosphate has greater healthy benefits. Most of the people suffering from tooth decay opt for homemade procedural toothpaste using calcium
1 Pages(250 words)Lab Report
Lab report
Another related objective was to apply equations for basic projectile motion in determining how high a rocket can fly. Since launching the model rocket, this is considered a projectile motion influenced by height of launch pad,
3 Pages(750 words)Lab Report
Lab report
The parabolic movement is the path traced by an object vertically, with constant acceleration, while the movement horizontally is at a constant velocity. The initial velocity and the projection angle determine
2 Pages(500 words)Lab Report
Lab report
For the first cycle, the mass of the water alone is the mass of the crucible lid and hydrate, less the mass of the crucible lid and residue after heating. That gives 22.678 – 22.460 = 0.218. The mass of the hydrated salt is the mass of the crucible lid and hydrated salt, less
1 Pages(250 words)Lab Report
Lab report
o calibrate the pressure transducer and then perform an uncertainty analysis and compare your pressure transducer calibration to the manufacturer’s calibration. 1. Excite the pressure transducer, with a voltage of 10v. The figure above had J17 and J18 as AO (Analog Out). It
5 Pages(1250 words)Lab Report
Lab report
The resistance (R) of a circuit component is the voltage drop (V) across the component divided by the current (I) across the device (R=V/I). It, therefore, means that if the resistance is high the voltage will also
3 Pages(750 words)Lab Report
Lab report
The results showed that the resistance were 0.0088 Ω and 0.003 Ω. DMM was used to measure the resistance of the small board resistors and the values recorded in table 1. Then the value of the 100 Ω resistor was varied by gathering a range of values of V
3 Pages(750 words)Lab Report
Lab report
The main aim of the experimental design was to assess and understand the different types of instruments used, for instance, the orifice meter, Rotameter, and positive displacement meter. The
3 Pages(750 words)Lab Report
Lab Report
From this mode, the shortest side of the triangle was represented by the distance between thumb nails (D), while the longest distance represented the distance from the ruler
2 Pages(500 words)Lab Report
Let us find you another Lab Report on topic Lab report for FREE!
Contact us:
Contact Us Now
FREE Mobile Apps:
  • About StudentShare
  • Testimonials
  • FAQ
  • Blog
  • Free Essays
  • New Essays
  • Essays
  • The Newest Essay Topics
  • Index samples by all dates
Join us:
Contact Us