Nobody downloaded yet

Lab report: discussion, conclusion, reference - Essay Example

Comments (0) Cite this document
This is because aluminum is versatile and has many desirable properties: light weight, nontoxic, pleasing appearance, ability to take high polish, high electric and thermal…
Download full paperFile format: .doc, available for editing
GRAB THE BEST PAPER94.9% of users find it useful
Lab report: discussion, conclusion, reference
Read TextPreview

Extract of sample "Lab report: discussion, conclusion, reference"

Download file to see previous pages Apart from primary aluminum obtained from bauxite, secondary aluminum and aluminum compounds are obtained through recycling. Recycling aluminum prevents depletion of aluminum ore reserves. Compared with primary production, production of secondary aluminum requires a lower amount of energy. (Davis, 1993)
One compound that can be obtained by chemical treatment of used aluminum is potash alum. Potash alum or common alum (potassium aluminum sulfate dodecahydrate, KAl(SO4)2.12H2O) is a double salt. The Al3+ ions in potash alum act as flocculating agent during water treatment and purification and also as a blood congealer in medicine. (Atkins & de Paula, 2006)
The objective of this experiment is to investigate a possible method for recycling used aluminum cans to potash alum. The experiment also aims to study the feasibility of this recycling process by calculating the percentage yield.
Collecting and weighing aluminum. The aluminum beverage can was washed. A 5×8 cm piece of aluminum was cut from the can. Paint from the outer surface of the can and plastic from the inner surface of the can were scraped off. The aluminum piece was cut into small squares. The aluminum squares were weighed and 0.996 g of aluminum was placed in a 250 mL beaker.
Addition of potassium hydroxide. To the aluminum in the beaker, 50 mL of 1.4 M potassium hydroxide was added. The reaction mixture of aluminum and KOH was heated on a hot plate in the hood. Heating was stopped when the mixture turned grey.
Vacuum filtering. Vacuum filtration apparatus was set up. The hot solution was vacuum filtered. The beaker used was rinsed with distilled water (5 mL) and this solution was also vacuum filtered. The filtrate obtained was cooled in an ice-water bath for a few minutes.
Addition of sulfuric acid and crystallization of potash alum. To the ...Download file to see next pagesRead More
Cite this document
  • APA
  • MLA
(“Lab report: discussion, conclusion, reference Essay”, n.d.)
Lab report: discussion, conclusion, reference Essay. Retrieved from
(Lab Report: Discussion, Conclusion, Reference Essay)
Lab Report: Discussion, Conclusion, Reference Essay.
“Lab Report: Discussion, Conclusion, Reference Essay”, n.d.
  • Cited: 0 times
Comments (0)
Click to create a comment or rate a document

CHECK THESE SAMPLES OF Lab report: discussion, conclusion, reference

Lab report

...?Lidia M. Lujan Lab report W14s1 Debate on Global Warming: Scientific Basis Global warming refers to the increase in the temperature of the earth's surface and troposphere. The term global warming is used interchangeably with “climate change,” referring to the other climatic changes aside from or due to increased global temperatures. The change in temperature is attributed directly due to increased in emission of greenhouse gases, largest concentration of which is carbon dioxide. The increased emission arises from human activities in the transport and energy sector (US Environmental Protection Agency). Other human activities like clearing of land, deforestation, and...
3 Pages(750 words)Lab Report

Discussion and Conclusion

...?Chapter 6 DISCUSSION AND CONCLUSION Discussion The statistics for the scale responses and total motivational scale scores from the above results mayprovide a reliable ground for further qualitative assessment of working experience through in-depth interviews, but as well constitute a group of stand-alone results. It is important to note first that the relatedness score, due to the nature of most questionnaire items, can be reasonably interpreted as the degree of separation (in case of the higher scores) experienced by the study participants in the community. According to the statistics for community relatedness score, presented in Table 2, the general sample responses indicate, first, a...
9 Pages(2250 words)Essay

Lab report

...the filter paper. An aspirator was used for 10 minutes to dry the crystals. A clean beaker was weighed. The crystals were transferred to the beaker and the beaker was weighed again. Results Weight of aluminum used in the experiment = 0.996 g Volume of 1.4 M KOH used = 50 mL Volume of 9.0 M H2SO4 used = 20 mL Weight of the empty beaker = 95.77 g Weight of potassium aluminum sulfate dodecahydrate and beaker = 109.60 g Weight of potassium aluminum sulfate dodecahydrate obtained= 13.83 g Discussion An aluminum surface reacts with atmospheric oxygen to form an inert oxide layer, which makes the metal corrosion resistant. This resistance is enhanced by anodizing: immersing in sulfuric acid and connecting to the positive...
2 Pages(500 words)Essay

Lab report

...SUMMARY SHEET Physics Laboratory Report -- Equilibrium of a Rigid Body Objective To be able to determine the center of gravity of a rigid body andpositions of weights with reference to that center that would establish equilibrium of forces and torques Method Obtain the weight (in Newton) of the meter stick and the average weight of the three meter stick clamps. Balance the meter stick in one of the clamps to determine its center of gravity. Place a clamp on one end of the stick to carry a 100-gram weight and slide the stick through the supporting clamp to locate the balance (position of the axis of rotation). Then place another clamp with a 200-g suspension and repeat the same previous step. Record...
3 Pages(750 words)Lab Report

Lab Report

... Last 4 digits of ID: 7989 Section: Lab Spring Laboratory 7:  Ecological Niche (15 points) Part I: Definitions and Backgroundinformation 1. The niche of an organism is the overall interactions of an organism with other organisms and its range of needs (Properties of microbes). 2. Organisms might compete for food, light, and space. 3. Evolution is the process of gradual development of organisms from simple structures to intricate forms over time. Competition affects the process of evolution in that the organism that is able to compete favorably for the available resources survives and continues to thrive, whereas the organism that cannot compete favorably dies and becomes extinct. Part II: Results Table 1: Effects of Temperature...
1 Pages(250 words)Lab Report

Lab Discussion

...Introduction This lab experiment was designed with the major objective of determining whether there is a direct relationship between its position and its average velocity in relation to time. . In order to achieve the above objective, the experiment made use of position time graph and velocity time graph. In which case, the slope of the position time graph was compared against the average velocity obtained from the velocity time graph. Discussion From the results attached, the slopes found in the position versus time graphs are reasonably close to the average velocities with only a few percent. Further, when carrying out the consistent, repeatable measurements the slopes of position versus time graph...
1 Pages(250 words)Lab Report

Lab Discussion

...Discussion question From the other car’s reference frame, our car is moving at a constant speed of; Our car was travelling at a constant speed hence its acceleration from the other car’s frame of reference is zero. The other car will also have an acceleration of zero as measured from our car’s reference frame. The reason is that both cars did not accelerate hence the car will be moving at a constant speed of -20km/hr as observed from our car. 2. a) Since the large box is not moving, the net force between me and a large box is zero hence the magnitude of force between me and the box are equal and opposite. b) The second box, however is much lighter, does not accelerate...
1 Pages(250 words)Lab Report

Lab Discussion

...You are traveling in a car going at a constant speed of 100 km/hr down a long, straight highway. You pass another car going in the same direction which is traveling at a constant speed of 80 km/hr. As measured from your car’s reference frame this other car is traveling at -20 km/hr. What the acceleration of your car is as measured from the other car’s reference frame? What the acceleration of the other car is as measured from your car’s reference frame? Give an explanation to your answers. Solution In this case, you need to consider the relative velocity with respect to the car you are travelling in. Therefore relative speed with reference to the car you are travelling...
1 Pages(250 words)Lab Report

Lab Discussion

...First Last Number 13 September Coefficient of kinetic and static friction: further discussions The wooden block placed on the varnish material experienced the least coefficient of static friction. This is because the surface of the varnish material is smoother than the other materials. Therefore, it offers little resistance to motion i.e. for a given regular force, the force of friction is smaller on varnish material compared to other materials according to equation below; The varnish material still have the smallest coefficient of friction compared to wood and sandpaper. 2 The uncertainty coefficient of kinetic friction for the varnish material had the least amount of uncertainty. This is because its values were...
1 Pages(250 words)Lab Report

Lab conclusion

...23 February Conclusion Strain measurements were obtained at the top of a cantilever beam. Strain gaugeswere used to obtain these strain measurements. In addition, the Poisson’s Ratio and the modulus of Elasticity of a material were utilized in the cantilever beam. They were from the strain measurements on the beam surface. It was possible to authenticate the measurements for this experiment got from the strain gages using the elementary linear beam theory. The elementary linear beam theory helped in computing the respective theoretical strain values. It is recommended that human errors be avoided. They can be evaded through the utilization of a more accurate measurement of the deflection in the tip. The reason being that...
1 Pages(250 words)Lab Report
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.

Let us find you another Essay on topic Lab report: discussion, conclusion, reference for FREE!

Contact Us