Nobody downloaded yet

Electrical circuits - Lab Report Example

Comments (0) Cite this document
Summary
Research session pertaining RLC circuit examines the response of this circuit under different conditions. The test takes various forms; the parallel RLC circuit, series RLC circuit, RC and LC. Testing criteria seek to…
Download full paperFile format: .doc, available for editing
GRAB THE BEST PAPER96.5% of users find it useful
Electrical circuits
Read TextPreview

Extract of sample "Electrical circuits"

Download file to see previous pages The report looks deeper into the literature review of electrical circuits and electronic components. The focus shifts to the analysis of electrical component analysis of their behavior and responses. Electronic components in electrical circuits include semiconductor devices diode, op amp and transistors. The electronic component features are explained in developed electrical networks. Performing signal processing in the semiconductor devices is meant to get information about input signal like RMS, peak value, the relative phase and the amplitude envelope. Nonlinear components are used in the feedback loop in examining the performance of diodes and op amp devices. Transistors have the capabilities of working with small-signal and large-signal characteristics exhibited by the bipolar junction transistor. Electrical circuit resonance behavior is imperative. The design research focuses on factors leading to vibration and resonant circuit components. Analysis of both parallel and series circuit have been reported vividly. Their performance in terms of the quality factor, bandwidth and power, are important factors determined. The transistors are used because they boost current components of the circuit. Black box is examined for various components to determine their values and responses to varying inputs of current and voltages. The report outline drifts into determining the values by elaborating on the procedures followed in the methodology. Results of the values of component rating have been documented and analyzed. The discussion and analysis section gives view about the results. RLC response characteristics in different connection conditions have been put out expounding on the effects of loading and use of active and passive devices in electrical circuits. They achieve application in designing of filters and communication equipment.
Signal systems make use of electronic ...Download file to see next pagesRead More
Cite this document
  • APA
  • MLA
  • CHICAGO
(“Electrical circuits Lab Report Example | Topics and Well Written Essays - 3750 words”, n.d.)
Electrical circuits Lab Report Example | Topics and Well Written Essays - 3750 words. Retrieved from https://studentshare.org/engineering-and-construction/1662763-electrical-circuits
(Electrical Circuits Lab Report Example | Topics and Well Written Essays - 3750 Words)
Electrical Circuits Lab Report Example | Topics and Well Written Essays - 3750 Words. https://studentshare.org/engineering-and-construction/1662763-electrical-circuits.
“Electrical Circuits Lab Report Example | Topics and Well Written Essays - 3750 Words”, n.d. https://studentshare.org/engineering-and-construction/1662763-electrical-circuits.
  • Cited: 0 times
Comments (0)
Click to create a comment or rate a document

CHECK THESE SAMPLES OF Electrical circuits

RF Integrated Circuits-electrical engineering

...?RF Integrated Circuits Wireless communications at RF are able to provide services to users during mobility, such as cell phones, pagers and broadcasting. The use of a high frequency carrier to produce a passband signal for transmission allows the implementation of smaller antennas, besides of an efficient management of the spectrum. Due to the development of the fabrication technology of integrated circuits, it is possible to design complex ICs that consist of analog and digital circuits on the same chip. Today, the CMOS technology is a good alternative for RF circuits integration, since it can work in the GHz frequency range with low noise figure. The...
1 Pages(250 words)Thesis Proposal

Electrical engineering

...Since my early childhood, I have always had passionate and curious about the inner mechanisms of electric gadgets around me; this led my parents to believing from an early age that I was destined to be an engineer. I wrecked a few electronic items in the house and got in trouble; however, as I grew older I was a regular hand around the house and I did most of the repairs on electronic stuff. In high school, I researched about engineering and one of my mentors and uncle who works as an electrical engineer encouraged me to major in the sciences. This was not difficult as I was in love with and excelled in mathematics and physics; I was not very strong in the arts so I opted to major mostly in technical...
3 Pages(750 words)Essay

Circuits design and application

...the output of the analyzer is audio, so it can use any scope for the display. The analyzer functions as a Tunable RF Voltmeter. This makes it function as a natural receiver / transmitter tracing signals. A display of the frequency is provided using the analyzer on a transmitter. Owing to the high sensitivity of the instrument signal tracing receiver circuits are permitted from the antenna through the low-level Radio Frequency stages. Whereas a conventional RF voltmeter adds up all the individual voltages as a summation without indicating the components it is not the case with a spectrum analyzer. Additionally the analyzer displays local oscillator signal and its frequency and injection levels. A tracking generator...
5 Pages(1250 words)Essay

Electrical Aplication

... of operation of an Earth Leakage Circuit Breaker (ELCB). The principle of operation of the vELCB is as follows. Under normal conditions the closed contacts of the vELCB feed the supply current to the load. The load is protected by a metal frame, such as in an electric cooker. The vELCB also has a relay coil, one end of which is connected to the metal frame and one end connected directly to ground. A shock risk will arise if a breakdown in the insulation occurs in the load which causes the metal frame to rise to a voltage above earth. A resultant current will flow from the metalwork through the relay coil to earth and when the frame voltage reaches a dangerous level, e.g. 50 volts, the current flowing through the relay coil... will be...
4 Pages(1000 words)Essay

Electrical

...Table of Contents Introduction Installation of the Circuit Board and Insertion of Faults Unit Characteristics of Transmission Lines This unit discusses the categories of transmission lines that are used. This is the correspondent circuit of a transmission line. The categories are as follows: characteristic impedance, impedance mismatch, attenuation, and distortion. Also, this unit talks about the transient actions of transmission lines, which are terminated by separate resistive load impedances. Ex. 1-1 Introduction to the Transmission Lines Circuit Board This section touches on familiarization with a variety of sections of the Lab-Volt TRANSMISSION LINES circuit board. Also, Thevenin equivalent of an electrical linear circuit... by the...
7 Pages(1750 words)Essay

Electrical power

...friendly form of green energy known as wind power. The process of extracting this kind of energy from the wind occurs when the wind turbines convert the kinetic energy from the wind into mechanical energy (which occurs when the blades of the wind turbine spin and turn the generator) which is then converted into electricity. Composed of a blade and an enclosed structure called a nacelle which contains a drive train, wind turbines are often observed in multiples covering several square kilometres known as wind farms, these turbines are mounted on bases between 80-100 meters high with offshore turbines being higher. (Right, Anton) Ideally the most sensible place for a wind turbine is as the name suggests, somewhere that is...
4 Pages(1000 words)Research Paper

Energy Transfer in electrical circuits

...Energy Transfer in Electrical circuits Energy Transfer in Electrical circuits In most of the energy generation systems, energy is converted from one form to another form. In power generation units, the chemical energy trapped in the coal is converted to thermal energy at first stage and then converted to electrical energy. In the similar manner, battery holds the energy that is generated through chemical reactions. Wind generators convert the aerodynamic energy of wind and convert it to electrical energy. Solar panels convert solar light energy into electrical energy, etc. In electrical...
6 Pages(1500 words)Research Paper

RC and RI circuits

... Introduction Capacitors are utilized in timing circuits within numerous devices. The time aids in maintenance of lightinglonger in order to remove the keys elements. The values are characterized with the time constants. This experiment measured the time constant of diverse capacitors in two conditions namely measuring the time constant for several seconds and measuring the time constants for microseconds. This experiment focuses on the examination of three electronic circuits containing passive components. The circuit diagrams were constructed utilizing Multisim software platform. The data and observation were recorded whilst simulating the above circuits. RC circuit contain both resistor connected in series and the capacitor... . The...
5 Pages(1250 words)Lab Report

Differential-Amp Circuits

...Laboratory Number: Op-Amp Circuits Lab Performance Submitted Dominick Lauria Lab Partner: Introduction: The instrumentation Amplifier is an improvement of differential amplifier circuit; its CMRR is not dependent on internal resistance of the sources. This is due to the summing point constraints at the lower and upper LM1458C inputs; there is no current is drawn from the signal source. These implies that the input impedance is seen by both sources as infinite therefore the output voltage is unaltered by the internal sources impedance, for example V1a=V2b=19.9V. Figure 1: Differential amplifier circuit Main Part: The First test: The circuit was built where Vs was 100Hz,...
3 Pages(750 words)Lab Report

Engineering electrical circuits and bernoulli science

...1. Principles of fluid flow In this principle, the flow of mass and volume of the fluids measures the amount of fluid moving in a space. Velo measure the fastness of the flow of the fluid. The relationship between the density, volume and the mass is shown in the equation below: Volume = Mass x density Or Q=m / ρ -------------------------------------------------------------- 1 For any volume flow, the speed depends on the pipe cross-sectional area. The link between the volume and the cross sectional area is shown n the equation 2 below. Volume flow (Q) = Velocity (v) * Area (A) Q = vA ----------------------------------------------------------------------2 If the pipe is circular, the velocity is takes as the area (A=π * r2... Principles of ...
4 Pages(1000 words)Assignment
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.

Let us find you another Lab Report on topic Electrical circuits for FREE!

Contact Us