We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Nobody downloaded yet

Displacement Using LVDT - Lab Report Example

Comments (0)
Summary
The objective of the study "Displacement Using LVDT" is to measure displacement using LVDT. The other objectives to be investigated in the study include obtaining voltage and LVTD pointer position data, discuss the behavior of voltage, plot a graph of average voltage against pointer position…
Download full paper
GRAB THE BEST PAPER
Displacement Using LVDT
Read TextPreview

Extract of sample
Displacement Using LVDT

Download file to see previous pages... Experimental procedure The procedure that was used to carry out the experiment was as follows 1. Multi-meter leads were connected to DC voltage supplier as shown in Figure No 2. Fixed 5V supply was set with the red wire. 2. Dial of digital multi meter was selected to DC volts. 3. Black lead was plugged in the COM and red lead was plugged in V socket of multi-meter as shown in Figure No 3. 4. The pointer of LVDT board was moved in 5mm intervals as shown in Figure No 4. The pointer position was changed from 0 – 50 mm in 5 mm interval. 5. The voltage on voltmeter was measured. 6. The procedure was repeated to get 2 sets of readings. The experimental data is placed in Table No 1. 7. Plot a graph for voltage verses displacement.Apparatus LVDT boardA digital voltmeter DC voltage supplier Setting up the experiment The first process in the experiment involves connecting the supply cables to the 5V sockets. In a situation where variable connections are used, there should be no exceeding 6V voltage supply. The next step involves connecting the output leads to the digital millimeter.With the connection, the LVDT voltage pointer is set as zero and then the pointer is moved at an interval of 5mm and the voltage output is recorded. The procedure is repeated two more times to obtain other readings. Plot a graph of voltage against distance.Comment on the results that are obtained from the graph plotted. ...Download file to see next pagesRead More
Comments (0)
Click to create a comment
CHECK THESE SAMPLES - THEY ALSO FIT YOUR TOPIC
Particle Size and Shape Measurements of Soot Using Image Analysis
It was found out that the mean particle area was about 0.26 cm squared. Particle 1 had a minimal area of 0.008 cm squared, and a maximum of about 0.31cm squared for the particles in the soot images. Additionally, the study found out that over 90% of the soot particles had 0.7 roundness with a mean value of about 0.73.
4 Pages(1000 words)Lab Report
Determining acceleration due to gravity using a simple pendelum
However, this force exhibits significant variations based on any given body’s location on earth’s surface besides influenced by both altitude and latitude (Hu?ttl 19). Premise asserting effects due to altitude states g changes inversely relative to the distance from the world’s center; hence, its values are 9.78m/s2 at equator and 9.83m/s2 at poles (Hu?
3 Pages(750 words)Lab Report
Disposition of Toxic Drugs and Chemicals

The author explains that Forensic Science deals with the study of serology and DNA especially in the forensic crime laboratory, “serology analysis” refers to the screening of evidence for bodily fluids. It is imperative to perform body fluid detection on evidentiary items before they are sent for DNA analysis.

8 Pages(1750 words)Lab Report
Temperature Monitor Simulation Using LabVIEW
As can be seen in the block diagram created using LabVIEW (Fig. 1), a Dial control was used as the source of the temperature signal. The signal was passed through Multiply and Add functions to convert it from a Celsius value to a Farenheit equivalent. A Waveform Chart was used to display temperature variation with time.
20 Pages(5000 words)Lab Report
Determination of Protein using Biuret Reagent
In case the bond is detected, copper (II) ions turn violet in an alkaline solution. In performing this test, several variants can be considered. Despite the name, the chemical does not contain burette ((H2N-CO-)2NH). This reaction is named using that name because it
3 Pages(750 words)Lab Report
Lab#7 Beam Analysis Using Photoelastic Methods
This method is important in determining the points of critical stress in a material and is utilized in determining the concentration of stress in geometries with
8 Pages(2000 words)Lab Report
Flow Measurement Using Venturi Meter
This means that it encompasses the actual experimental set-up, the used apparatus, the achieved results, the theoretical framework of this concept, the analysis and discussion of the attained
9 Pages(2250 words)Lab Report
Lab report (Using NMR)
The chemical shift targeting each nucleus can be correlated to the chemical environment with the scalar coupling showing an indirect interaction between the individual nuclear that are mediated by the electrons found in the chemical bond and appropriate
4 Pages(1000 words)Lab Report
Measurement and Instrumentation LVDT sheet
Its main disadvantages are its dynamic response and the effects of the exciting frequency (Kim et al., 2010). General guidelines regarding the selection of an LVDT for a certain application can be found in (Herceg, 2006). The basic construction of
2 Pages(500 words)Lab Report
Magnetization on Voltage Using Metals and Semiconductors
The author of the paper explains that hall effect is the voltage difference in an electrical conductor which normally occurs when a magnetic field is applied to a rectangular shaped conductor at right angles when it is carrying electric current. Theoretically, hall effect is explained by the principles of Lorentz force.
4 Pages(1000 words)Lab Report
Let us find you another Lab Report on topic Displacement Using LVDT for FREE!
Contact us:
+16312120006
Contact Us Now
FREE Mobile Apps:
  • About StudentShare
  • Testimonials
  • FAQ
  • Blog
  • Free Essays
  • New Essays
  • Essays
  • The Newest Essay Topics
  • Index samples by all dates
Join us:
Contact Us