CHECK THESE SAMPLES OF Sorting device for metal stampings experiment / FLUID POWER LAB
In addition, a lab coat, goggles, and tongs were required for safety reasons.... We assembled the cell in the first lab session and determined the current and voltage.... In this experiment, a solar cell would be constructed for conversion of sunlight energy into electrical power for use in electrolysis of water.... Thus, this experiment aims to construct a dye-sensitized solar cell and to measure its current and voltage as well as using the cell to convert light into electricity for electrolysis of water....
5 Pages
(1250 words)
Lab Report
The Pitot is capable of measuring the fluid velocity via the conversion of… The Pitot-static tube, therefore, is a flow velocity meter that measures fluid velocities in localized point; they do not take an averaged velocity across the larger section.... The conversion of the resulting differential pressure measurements into respective fluid velocity heavily depends on the specified fluid's flow regime a Pitot tube is measuring (Spurk and Aksel, 2008)....
5 Pages
(1250 words)
Lab Report
The lab report "Fluid Mechanics for Engineers" involves the analysis of the energy losses in pipes.... hellip; The equipment necessary for this work to be carried out will be collected and assembled as provided in the lab manual.... Energy losses in pipes normally result from friction that occurs between the walls of the pipe and the fluid and the internal friction in the particles of the fluid.... On the location of the pipe whereby the streamlines are not straight such as the bends, piping junctions, valves contraction, and expansion joints and the inlets and outlets of the reservoirs, minor head losses are experienced (fluid mechanics: Online)....
7 Pages
(1750 words)
Lab Report
Analysis and DiscussionThe findings ontained from the measurements of the results of the experiment reveals a number of aspects and properties of Hall effect.... The variation of voltage was studied with changing distance and plots were obtained.... The paper "Magnetization on Voltage Using Metals and Semiconductors" explains that a voltage is generated in an electrical conductor carrying an electric curren when a magnetic field is applied to it at right angles....
4 Pages
(1000 words)
Lab Report
The paper "The experiment on the Determination of Tensile Strength of Metals" describes that the tensile strength of metals varies according to the amount of load they are supposed to carry out.... s from the topic of this laboratory experiment, the report is confined to the tensile properties of metals.... Figure 1 below shows a tensile testing machine with features similar to the one used to conduct this experiment.... A doge-bone-shaped specimen is gripped at its two ends and pulled apart during a typical tensile experiment to elongate at a determined rate to its breakpoint....
8 Pages
(2000 words)
Lab Report
t is paramount to wear safety glasses before beginning the experiment since broken pieces of metals can cause harm to your eyes.... Additionally, gloves help protect the person conducting the experiment from any residue on the machine and samples.... hellip; The results clearly show that metal 2 that yields at an approximate load of 1.... metal 1is the next in the list with a yielding point at an approximate load of 6.... Lastly, metal 1 tops the list with a yielding point at 10....
8 Pages
(2000 words)
Lab Report
Chapter 1: Introduction
Bernoulli's principle, named after its founder, Daniel Bernoulli, asserts that "as the speed of a moving fluid (liquid or gas) increases, the pressure within the fluid decreases.... This is different from the continuity equation, which only applies a connection between n speed of the fluid and the cross-sectional area measured for a pipe in which the fluid moves.... This includes, the fluid used must be frictionless at a constant density, in which case, steady flow is a must....
8 Pages
(2000 words)
Lab Report
This lab report highlights the association between pressure and the rate of fluid flow through the piping system using a venturi meter.... The experiment helps in the understanding of the changes in the cross-sectional area of the pipe, which affects the fluid flow rate and the pressure.... Control of flow requires special mechanics that reduce the pressure generated by the pipe and the fluid flowing inside (Miller, 1996; USBR, 1996).... Most importantly, the experiment was instrumental in opening the eyes of the students on the practical application of piping models and how they work with respect to changes in the speed of the fluid in the system and how to control such parameters to improve the motion of fluids....
10 Pages
(2500 words)
Lab Report