Free

V8 Engine Block Assembly - Assignment Example

Add to wishlist

Summary

The author describes the main part of a V8 engine which is called the block. The block is one of the largest parts of the engine and is where all of the other parts are mounted. The V8 engine can either be mounted on an engine stand or bolted directly into the vehicle and then assembled. …

Download full paper File format: .doc, available for editing

GRAB THE BEST PAPER92% of users find it useful

Read Text

Subject: Technology
Type: Assignment
Level: College
Pages: 1 (250 words)
Downloads: 3
Author: moniquecassin

Extract of sample "V8 Engine Block Assembly"

Depending on which vehicle the engine is going in will depend on whether or not the engine can be assembled on a stand. The first thing to go onto the block is the camshaft. It is important to keep very clean while installing all the engine components. It is important to lube the cam while installing. Second, the crank shaft must be installed and checked. After the crank shaft is installed it is necessary to install the rear main seal with gaskets if needed. Third, the timing gear and chains need to be properly installed.

After the timing is accurate, the oil wrist pins, rod bearing, and the rings need to be properly installed on the pistons. Next, it is important to properly oil all cylinders, bearing, rings and crankshaft. Then it is very important to install the pistons. The pistons need to be at a certain compression to prevent damage.

CHECK THESE SAMPLES OF V8 Engine Block Assembly

High Eco-Car Engine

HIGH ECO CAR engine PROJECT REPORT Name: Instructor: Institution: Date: 1 2 Table of Contents LIST OF TABLES AND FIGURES …………………………………………………….... 0 3 LISTOFTABLES AND FIGURES Tables and Graphs: Table 1: Properties of Hi-Eco engine………………………………………….... Table 2: Evaluation of engine Properties of option 1 and 2………….... 7 Figures: Figure 1: BMW Turbo Charged engine……………………………....

10 Pages (2500 words) Term Paper

Lubricator for Gas Generators

Keywords: natural gas engine, lubricity, valve failure, exhaust valve, head assembly Table of Contents Statement of the Problem 11 Rationale 11 Assumptions 12 Limitations 12 Nomenclature 13 Terms.... 10 Figure 2 - Arrangement of inlet valve and exhaust valve in a single cylinder engine configuration 22 Figure 3 - The gas genset used for the current research sourced from (Green Power, 2013) 23 Figure 4 - MTBF against lubrication feed rate 25 Figure 5 - Lubricator body with bracket welded on 29 Figure 6 - Lubricator graduation cylinder 30 Figure 7 - Lubricator end tail for insertion into air plenum 30 Figure 8 - Complete lubricator assembly including lubrication adjustment screw (shown on the left bottom corner) 31 Figure 9 - Proposed air plenum base 32 Figure 10 - Proposed air plenum top cover 33 List of Tables Table 1 - Budget for the current research....

14 Pages (3500 words) Research Paper

Henry Ford the founder of the Ford Motor Company

He wanted to mix together the various characteristics from other industries such as the standardized parts as Eli Whitney had used with gun manufacturing or assembly line methods George Eastman tried in photo processing.... At fifteen, he was able to build his own steam engine and at sixteen years old, young Henry left Dearborn and went to the town's nearby city.... With the Quadricycle, his theories no longer remained as is - like the gas engine he built on his kitchen table in the 1890's, which was just an engine with nothing to power....

9 Pages (2250 words) Essay

The connecting rod for a typical passenger car engine

Connecting rod being the part of the engine and drive system, has to run with other components like engine block, gearbox, cam etc.... When we are talking about the connecting rod or any part of the automobile engine, any component cannot be compared or explained in isolation....

6 Pages (1500 words) Essay

Trends in Crankshaft Materials

However, it has been widely used in the internal combustion engine.... Though the modern automobile in the form that is currently seen took a number of decades to develop, the use of crankshafts in powered automobiles is as old as the first steam engine propelled vehicle developed by Joseph Cugnot in 1769 (Derry and Williams, 1993).... Crankshafts ever since have been satisfying the need to convert the-to and fro motion of the engine, be it steam powered, diesel powered or any other type of engine, to the circular motion of the wheels....

16 Pages (4000 words) Case Study

Electro-Mechanical Control Systems Assignment

When the nut assembly moves with respect to the rotating shaft, the balls move inside the nut assembly.... In this manner, engineers have to undergo a deep research phase to solve the engineering problems systematically.... Engineers found it easier to develop new approaches in… The problems associated with one engineer working in a bounded environment are like to be faced by other engineers working in another bounded environment....

5 Pages (1250 words) Assignment

Electrical and Electronic Engineering

This work "Electrical and Electronic Engineering" describes microcontrollers as a whole without being specific on one type or kind of a microcontroller in order to comprehend the concepts behind all microcontrollers.... The author outlines the microcontroller as a single entity, its history, the types, utilization, application, development tools, its features....

6 Pages (1500 words) Research Proposal

Engine Strip and Build

From the paper "engine Strip and Build" it is clear that the aims of the engine practical workshop were obtained and we were able to achieve the combustion ratio for honda engine that is 8.... Alternator bracket should be made of very strong materials because it's carrying an alternator that is connected to the engine pulley by a high tension v-belts, the bracket is also subjected to vibration because when the belt is in use, its elastic properties cause the bracket to vibrate....

10 Pages (2500 words) Lab Report